Effect of Compaction Pressure on a Stabilized Rammed Earth Behavior
DOI:
https://doi.org/10.56294/sctconf2024821Keywords:
Rammed Earth, Compressive Strength, Thermal Conductivity, Durability.Abstract
The current work addresses the effect of compaction pressure on durability against water ingress, compression behavior, and thermal conductivity of rammed earth specimens stabilized with fly ash geopolymer. These properties were investigated for specimens made from 25 % fly ash and proportions of sand, silt, and clay. The fly ash was activated with 2M sodium hydroxide solution, and the specimens were compacted statically to 5, 10, or 25 MPa. Reference mixtures containing the raw material (i.e., sand, silt, and clay) were also prepared for comparison. The results of the durability test on stabilized specimens indicated excellent resistance to deterioration caused by water ingress, unlike those made from raw materials which almost failed completely. The materials elastic stiffness and compressive strength were both improved substantially with the inclusion of fly ash geopolymer and with compaction pressure increase. The inclusion of geopolymer resulted in 6 to 10 folds improvement in the compressive strength. For instance, the stabilized specimens provided a compressive strength of 2,7 MPa when compacted to 5 MPa, compared to only 0,3 MPa provided by the unstabilized specimen. Likewise, an increase in compaction pressure from 5 to 25 MPa, resulted in an increase of 56 % in the compressive strength. The thermal conductivity of the stabilized material was in the order of 0,4-0,5 W/ (m.K) and was considered relatively low comparing to that of other competitors such as normal concrete and even lower than that of the raw material by about 18 %. The thermal conductivity increased by about 20 % with compaction pressure increase from 5 to 25 MPa. It seems that the increase in the stiffness and strength with compaction pressure increase can compensate the small undesirable increase in the thermal conductivity
References
1. C. J. Kibert, "Deconstruction: the start of a sustainable materials strategy for the built environment," Industry and environment, vol. 26, no. 2, pp. 84-88, 2003.
2. D. Maskell, A. Heath, and P. Walker, "Laboratory scale testing of extruded earth masonry units," Materials & Design, vol. 45, pp. 359-364, 2013.
3. P. Donkor and E. Obonyo, "Earthen construction materials: Assessing the feasibility of improving strength and deformability of compressed earth blocks using polypropylene fibers," Materials & Design, vol. 83, pp. 813-819, 2015.
4. J.-C. Morel, A. Pkla, and P. Walker, "Compressive strength testing of compressed earth blocks," Construction and Building materials, vol. 21, no. 2, pp. 303-309, 2007.
5. H. Danso, B. Martinson, M. Ali, and C. Mant, "Performance characteristics of enhanced soil blocks: a quantitative review," Building Research & Information, vol. 43, no. 2, pp. 253-262, 2015.
6. H. N. Atahan, B. Y. Pekmezci, and E. Y. Tuncel, "Behavior of PVA fiber-reinforced cementitious composites under static and impact flexural effects," Journal of Materials in Civil Engineering, vol. 25, no. 10, pp. 1438-1445, 2013.
7. H.-b. Zhu, M.-z. Yan, P.-m. Wang, C. Li, and Y.-j. Cheng, "Mechanical performance of concrete combined with a novel high strength organic fiber," Construction and Building Materials, vol. 78, pp. 289-294, 2015.
8. S. Byrne, "Fire-resistance test on a landbearing 250 mm thick adobe blockwork walls," Experimental Building Station, Dept. of Housing and Construction Technical Record, no. 490, 1982.
9. K. Heathcote, "Durability of earthwall buildings," Construction and building materials, vol. 9, no. 3, pp. 185-189, 1995.
10. K. B. Ren and D. A. Kagi, "Upgrading the durability of mud bricks by impregnation," Building and Environment, vol. 30, no. 3, pp. 433-440, 1995.
11. P. Walker, "Bond characteristics of earth block masonry," Journal of Materials in Civil Engineering, vol. 11, no. 3, pp. 249-256, 1999.
12. Y. H. Navarro, "Tap-tap: guía didáctica de actividades infantiles de sensibilización," Loggia: Arquitectura y restauración, no. 30, pp. 128-128, 2017.
13. S. Bestraten, E. Hormias, and A. Altemir, "Earthen construction in the 21 rst century," Informes de la Construcción, vol. 63, no. 523, pp. 5-20, 2011.
14. J. Fernandes, M. Peixoto, R. Mateus, and H. Gervásio, "Life cycle analysis of environmental impacts of earthen materials in the Portuguese context: Rammed earth and compressed earth blocks," Journal of cleaner production, vol. 241, p. 118286, 2019.
15. M. B. Mansour, A. Jelidi, A. S. Cherif, and S. B. Jabrallah, "Optimizing thermal and mechanical performance of compressed earth blocks (CEB)," Construction and Building Materials, vol. 104, pp. 44-51, 2016.
16. F. El Fgaier, Z. Lafhaj, E. Antczak, and C. Chapiseau, "Dynamic thermal performance of three types of unfired earth bricks," Applied Thermal Engineering, vol. 93, pp. 377-383, 2016.
17. A. W. Bruno, D. Gallipoli, C. Perlot, and H. Kallel, "Thermal performance of fired and unfired earth bricks walls," Journal of Building Engineering, vol. 28, p. 101017, 2020.
18. P. Ghadir and N. Ranjbar, "Clayey soil stabilization using geopolymer and Portland cement," Construction and Building Materials, vol. 188, pp. 361-371, 2018.
19. S. Mahvash-Mohammadi, S. Lopez-Querol, and A. Bahadori-Jahromi, "Effect of fly ash on the bearing capacity of stabilised fine sand," Proceedings of the ICE-Ground Improvement, 2017.
20. D. ASTM, "422," Standard test method for particle-size analysis of soils, 2007.
21. D.-. ASTM, "Standard test methods for liquid limit, plastic limit, and plasticity index of soils," D4318-10, 2010.
22. D. ASTM, "Standard test method for engineering purposes (unified soil classification system)," D2487, 2017.
23. D. ASTM, " Standard test methods for specific gravity of soil solids by water pycnometer," D854, 2014.
24. S. Yahya and M. Al-Sharrad, "On the preparation of rammed earth material stabilized with fly ash geopolymer," 2023.
25. D. ASTM, "Standard Test Method for Unconfined Compressive Strength of Cohesive Soil," D2166-16, 2016.
26. D. ASTM, "Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures (ASTM International). www.astm.org," ASTM D7012-14 2014.
27. C. ASTM, "Standard Test Method for Thermal Conductivity of Refractories by Hot Wire (Platinum Resistance Thermometer Technique)," C1113-2013, 2013.
28. D, "Deutsches Institut Fur Normung E.V. (German National Standard) Earth Blocks – Terms and Definitions, Requirements, TestMethods," DIN 18945, 2013.
Published
Issue
Section
License
Copyright (c) 2024 Ahmed K. Ftaikhan , Muayad A. Al-Sharrad (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
The article is distributed under the Creative Commons Attribution 4.0 License. Unless otherwise stated, associated published material is distributed under the same licence.
